Zenoah BT225 Manual de usuario

OWNER/OPERATOR MANUALLINE TRIMMERBT01-00001 (501)The engine exhaust from this productcontains chemicals known to the Stateof California to cause cance

 10 • IF SOMEONE COMES1. Guard against hazardous situations at all times.Warn adults to keep pets and children awayfrom the area. Be careful if you

5. For safe operationrefill the tank of the unit in any place where thereis a boiler, stove, wood fire, electrical sparks,welding sparks, or any other

 12  MOUNTING ENGINE (SE1)1. Loosen the bolts temporarily attached to theclutch housing.2. Push the driveshaft toward the gearcase androtate it by

6. Set up INSTALLING CUTTING HEAD (SE6)1. While locking the gear shaft by inserting theattached bar into the upper holder and thehousing. 2. Rotate t

 14 7. Fuel RECOMMENDED MIXING RATIOGASOLINE 50:OIL 1• Exhaust emission are controlled by thefundamental engine parameters andcomponents(eq., carbu

7. Fuelagain for at least one minute. As someoils may be difficult to agitate dependingon oil ingredients, sufficient agitation isnecessary for the en

 16  STARTING ENGINE1. Rest the unit on a flat, firm place. Keep thecutting head off the ground and clear ofsurrounding objects as it will start ro

8. Operation STOPPING ENGINE1. Release the throttle lever and run the engine fora half minute.2. Shift the ignition switch to the STOP position.• Exc

 18 3. You can avoid thrown debris by sweeping fromyour left to the right.4. Use a slow, deliberate action to cut heavygrowth. The rate of cutting m

9. Maintenance•Always be sure to stop the engine before inspecting the brushcutter for problems orperforming maintenance.• Never alter the brushcutter

SAFETY FIRSTInstructions contained in warnings within thismanual marked with a symbol concerncritical points which must be taken intoconsideration to

 20 9. Maintenance8 11 1412910 121315THISSIDE UPTHISSIDE UPWINDLINE

•Make sure that the engine has stopped and iscool before performing any service to thebrushcutter. Contact with moving cuttinghead or hot muffler may

 22  MUFFLER•Inspect periodically, the muffler for loosefasteners, any damage or corrosion. If anysign of exhaust leakage is found, do not usethe b

9. Maintenancebrushcutter. Note that it is necessary to removethe plug guard shown in Figure 20 in order to beable to view the upper part of the cylin

11. Troubleshooting guideCase 1. Starting failure CHECK PROBABLE CAUSES ACTIONfuel tank ➞ incorrect fuel ➞ drain it and with correct fuelfuel filter ➞

12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does not warr

12. Parts list  26 Fig.1 DRIVE UNIT BT225 (S/N 000001 and up)

Key# Description Part Number Q'tyFig.1 DRIVE UNIT BT225 (S/N 000001 and up)Key# Description Part Number Q'ty1PIPE COMP. BT01-50810 12 DRIVE

Fig.2 ENGINE UNIT BT225 (S/N 50100000 and up) 28 12. Parts list

Key# Description Part Number Q'tyFig.2 ENGINE UNIT BT225 (S/N 50100000 and up) 29 Key# Description Part Number Q'ty1 CYLINDER 5580-12110

2. Specifications BT225Overall size(LxWxH)························································ 70.0(1780)x14.0(355)x9.5(241) in(mm)Dry weight w/o

EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMa

Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., parl'intermédiaire de n'importe quel revendeur

©Printed in JapanKOMATSU ZENOAH AMERICA INC.4344 Shackleford Road Suite 500Norcross, Georgia 30093

 4 (1) Read owner's manual before operating this machine.(2) Wear head, eye and ear protection.(3) Warning/Attention(4) Keep all children, byst

For safe operation and maintenance,symbols are carved in relief on the machine.According to these indications, please becareful not to make a mistake.

 6 5. For safe operation1. Read this manual carefully until youcompletely understand and follow all safetyand operating instructions. 2. Keep this m

b. At night, at times of heavy fog, or at any othertimes when your field of vision might belimited and it would be difficult to gain a clearview of th

 8  BEFORE STARTING THE ENGINE1. The area within a perimeter of 50 feet (15m) ofthe person using the product should beconsidered a hazardous area i

Never place the throttle into the high speedposition when starting the engine.3. After starting the engine, check to make surethat the cutting attachm